FenceTrac standard gate kits can be adjusted to any width narrower than the standard kit size by cutting the top and bottom rails to fit the opening. No welding is required. Standard single gate kits ship at 4-foot and 6-foot widths, and standard double gate kits ship at 8-foot and 12-foot widths. All four can be trimmed on site to match the exact opening.
The Short Answer
Yes. Every standard FenceTrac gate kit is adjustable. The installer cuts the top rail and bottom rail to the desired width, reassembles the gate frame, and installs the infill. The aluminum frame cuts cleanly with standard metal-cutting tools, and the finished gate retains the same structural integrity as a full-width kit.
How Gate Width Adjustment Works
The adjustment process is straightforward and happens on site during installation.
Measure the Opening
The installer measures the clear opening between the gate posts. This measurement determines how much material to remove from the top and bottom rails.
Cut the Top and Bottom Rails
The top rail and bottom rail are the horizontal pieces of the aluminum gate frame. The installer marks the cut line on each rail and trims them to the new width using a standard metal-cutting saw or angle grinder. The side channels stay at their original height.
Reassemble and Install Infill
The trimmed rails bolt back to the side channels using the same fasteners included in the kit. The infill boards slide into the frame channels, and the gate is ready to hang. The result is a clean, precise fit with no visible evidence of modification.
Watch: FenceTrac Gate Kit Assembly
This video demonstrates the full gate kit assembly process, including how the frame components connect and how infill boards are installed.
Why This Matters for Fence Design Planning
Not every gate opening falls on a standard 4-foot or 6-foot measurement. Existing structures, property lines, and site conditions often create openings at non-standard widths.
With conventional fence gates, a non-standard opening usually means ordering a custom gate at a higher cost and longer lead time. FenceTrac’s standard gate kits eliminate that problem. The installer starts with the next size up, cuts the rails to fit, and finishes the job on the same day.
This makes FenceTrac gate kits practical for retrofit projects, tight side yards, and any installation where the opening was not designed around standard gate widths.
Adjustable Widths by Gate Kit Size
| Standard Kit | Kit Width | Adjustable Down To | How |
|---|---|---|---|
| Single gate (standard) | 4 feet | Any narrower width | Cut top and bottom rails |
| Single gate (wide) | 6 feet | Any narrower width | Cut top and bottom rails |
| Double gate (standard) | 8 feet | Any narrower width | Cut top and bottom rails on each leaf |
| Double gate (wide) | 12 feet | Any narrower width | Cut top and bottom rails on each leaf |
For double gates, the installer divides the total desired width between the two leaves and cuts each one accordingly. Both leaves retain the same stainless steel hinges, lockable latch, and commercial drop rod included in the original kit.
What About Wider-Than-Standard Openings
Rail cutting only works in one direction: narrower than the kit size. If the opening is wider than the largest standard kit (6 feet for single gates, 12 feet for double gates), the standard kits cannot be stretched to fit.
For wider openings, FenceTrac builds custom steel welded gates to the exact dimensions required. Cantilever slide gates are available for commercial openings up to 32 feet wide. Custom gates ship fully welded and ready to install.
No Welding, No Special Tools
The entire adjustment process requires no welding and no special tools. The aluminum gate frame is cut with a metal-cutting blade and reassembled with the bolt-together fasteners included in the kit. Any fence installer with standard power tools can make the adjustment on site.
This keeps installation costs and timelines the same as a standard-width gate. There is no fabrication step, no shop time, and no delay waiting for a custom order.
Related Questions
Do FenceTrac gates come as a kit or fully assembled? All standard FenceTrac gates ship as a complete kit. The frame components, hardware, and fasteners arrive together, ready for on-site assembly with no welding required.
What is the standard width for a single FenceTrac gate? Single gate kits ship at 4-foot and 6-foot widths, both adjustable to any narrower opening.
What is the standard width for a double FenceTrac gate? Double gate kits ship at 8-foot and 12-foot widths, with both leaves adjustable by cutting the horizontal rails.
See Also
What is channel frame modular fencing for details on how the FenceTrac frame system accepts infill. Adding an automated opener to a FenceTrac gate for information on automation hardware compatibility.
Get a Quote for Your Gate Project
FenceTrac ships fence systems and gate kits nationally and has been manufacturing engineered fencing in the USA since 2012.
Every system carries a 20-year warranty and is engineered for long-term performance with minimal maintenance.